Avery ZG352 Uživatelský manuál

ZG352 DIRECT THERMAL BAR CODE PRINTERUSER’SMANUAL

2.2.2 Interior View 1 9 7 2 (ZG352 Model) 38 1. Top cover2. Media holder3. Media guide4. Printhead5. Gap sensor (receiver)6. Gap sensor (trans

5

2.2.3 Rear ViewZG352 model    1. Power switch 2. Power jack socket3. USB interface4. Fan-fold paper entrance chuteNote: The interfac

 7

3. Setup 3.1 Setting Up the Printer 1. Place the printer on a flat, secure surface.2. Make sure the power switch is set to “off”.3. Connect the prin

3. Separate the media holders to the label roll width.ZG352 model 4. Place the roll between the holders and close them onto the core.5. Place the p

6. Close the top cover gently and make sure the cover latches securely. ZG352 model  7. Use “Diagnostic Tool” to set the media sensor type and

•Loading path for roll labelsZG352 model 11

3.2.2 Loading External Media 1. Open the printer’s top cover and separate the media holders to fit the media width. 2. Press down the med

Calibrate 13

ContentsCopyright Declaration 1. Introduction ii1.1 Product Introduction ii1.2 Compliances ii52. Operations Overview 12.1 Unpacking and Inspection12

3.2.3 Loading Media in Peel-off Mode (Option)1. Refer to section 3.2.1 to load the media. 2. Open the top cover and peel-off panel after calibrated

4. Push the peel-off panel back to the printer.5. Close the top cover gently. 6. Press the FEED button to test. Backing paper (Liner)Note: Please c

3.2.4 Loading Media in Cutter Mode (Option)1. Refer to section 3.2.1 to load the media. 2. Lead the media through the cutter paper opening. Cutter p

 Note: Please calibrate the gap/black mark sensor when changing media.17

3.3 Diagnostic Tool The Diagnostic Utility is enclosed in the CD disk \Utilities directory from. The DiagnosticUtility is a toolbox that allows u

3.3.2 Printer Function (Calibrate sensor, Ethernet setup, RTC setup) 1. Select the PC interface connected with bar code printer.2. Click the “Functi

3.4 Setting Ethernet by Diagnostic Utility The Diagnostic Utility is enclosed in the CD disk \Utilities directory . Users can use Diagnostic

 3.4.2 Using Ethernet interface to setup Ethernet interface1. Connect the computer and the printer to the LAN.2. Turn on the printer power. 3. Sta

 “Set IP” to take effect the settings. Users can also change the “Printer Name” by another model name in this fields then click“Set Printer Name” to

 3.5 Install MicroSD Memory Card1. Open the SD memory card cover.2. Insert the MicroSD card into the socket. 3. Close the memory card cover.* R

4.3.4 Set Black Mark Sensor as Media Sensor and Calibrate the BlackMark Sensor 324.3.5 Set Gap Sensor as Media Sensor and Calibrate the Gap Sensor32

 - Folders/files stored in the SD card should be in the 8.3 filename format24

 3.6 Mount the Printer on the WallThere are three holes in the bottom of printer. Printer can be mounted on the wall by the 3.0mm~3.5mm screw head s

 26

 4. LED and Button FunctionsThis printer has one button and one three-color LED indicator. By indicating the LED with different color and pressing t

  Power on utilities The LED color will be changed as following pattern: 4. Set black mark sensor as media sensor and calibrate the black marksen

 4.3.2 Gap/Black Mark Calibration, Self-test and Dump ModeWhile calibrate the gap/black mark sensor, printer will measure the label length, print th

 Self-test Printer will print the printer configuration after gap/black mark sensor calibration. Self-test printout can be used to check if there is

 ASCII Data Hex decimal data related to left column of ASCII data Note: 1. Dump mode requires 2” wide paper width.2. Turn off / on the power

 4.3.4 Set Black Mark Sensor as Media Sensor and Calibrate the Black Mark SensorPlease follow the steps as below.1. Turn off the power switch. 2. Ho

 The AUTO.BAS program can be interrupted without running the program by the power-onutility. Please follow the procedures below to skip an AUTO.BAS

i

    5. Troubleshooting The following guide lists the most common problems that may be encountered when operating this bar code printer. If the

    5.2 Print Problem ProblemPossible CauseRecovery ProcedureNot Printing Check if interface cable is well connected to the interface connect

          5.3 LCD display This section lists the LCD display messages that you may encounter when operating the printer. Also, i

     6. Maintenance This session presents the clean tools and methods to maintain your printer.1. Please use one of following material to cl

 •Please use 100% Ethenol. DO NOT use medical alcohol, which may damage the printer head. Regularly clean the print head and supply sensors once cha

 Revise History392010/3/12 Camille Date Content Editor 2009/8/10 Revise 2.2.2 section Camille 2009/9/7 Revise 3.3 Diagnostic Tool section Camil

 Avery Weigh-Tronix USA 1000 Armstrong Dr. Fairmont MN 56031 USA Tel: 507-238-4461 FAX: 507-23

1. Introduction 1.1 Product IntroductionThank you for purchasing a ZG352 bar code printer. Although the printer has a small footprint, it delivers

"ORSICHT" Explosionsgetahr bei unsachgemen Austausch der Batterie. Ersatz nur durch denselben odereinem vom Hersteller empfohlenem nlichen

2. Operations Overview2.1 Unpacking and InspectionThis printer has been specially packaged to withstand damage during shipping. Please carefully ins

2.2 Printer Overview 2.2.1 Front View ZG352 model   1. Top cover open lever2. MicroSD card socket3. Media view window4. LED indicator5. Feed

3